Die lager sind ein gebräuchliches lager, das die radlager mit radauselementen verbindet und so strukturelle vielfältig, wandlungsfähig und gut wechselseitig lagernde lager entwickelt. Die lager haben mehrere vorteile in der mechanischen anlage, die lassen sich wie folgt zusammenfassen:
1. Externe kapazitäten:
Hohe sphären - und axiallaststoffe sowie eine hohe tragkraft können dieser fracht für mechanisches gerät bei verschiedenen lasten und hochgeschwindigkeit standhalten.
2. Installation:
Der einbau Von löchern und klingen auf dem gerät lässt die schwierigkeit und die kosten der installation drastisch sinken.
3. Leben lang:
Holzlager hinzufügen, um reibungen und abnutzung zu reduzieren und so die langlebigkeit der lager zu erhöhen.
4. Leicht zu bedienen:
Einstiegslöcher sind dazu geeignet, gleitmittel leicht aufzufüllen und zu ersetzen, was die wartung sowohl schwierig als auch teuer macht.
Installation and Fixation of Bearings
(1) Bearing with Top Screws
This type of bearing has two set screws at an angle of 120° installed on one end of the wide inner ring, and the set screws tighten the inner ring of the bearing to the shaft. During installation, sufficient torque is required to ensure the fastening of the bearing to the shaft. (Table 10) provides the recommended tightening torque for the set screws.
Tightening torque of set screws, Bearing specifications, Set screws (metric/imperial), Maximum tightening torque
If the bearing operates under the following conditions: 1) The bearing vibrates; 2) The bearing has relative movement; 3) The bearing is subject to heavy loads or high rotational speeds, a tightening slot or recess should be provided at the corresponding position of the set screw on the shaft
(2) Bearing with Locking Sleeve
This bearing has a 1:12 taper on the inner hole. During installation, first insert the sleeve into the bearing hole, then embed the lock washer, and finally install the nut. When installing the shaft, first tighten the nut as much as possible by hand, and then use a wrench to turn it in 2/5 to 3/5 turns. After tightening the nut, bend the lock washer into the lock groove; otherwise, relative sliding between the shaft and the sleeve may occur due to loose nuts.
(3) Bearing with Eccentric Sleeve
The elongated end of the inner ring of this bearing has an eccentric boss, and there is also an eccentric groove on one side of the eccentric sleeve. When installing it on the shaft, align the eccentric boss with the eccentric groove, first tighten the eccentric sleeve in the direction of shaft rotation, and then tighten the set screw on the eccentric sleeve.
(4) Installation of Bearing Housings
The correct installation sequence for bearings with housings should be: first install the housing, then install the shaft. In principle, the bearing housing can be installed anywhere, but to ensure the service life of the bearing, the installation surface must be flat and secure.
For bearings with vertical or flanged housings, the requirement for the installation surface inclination angle should not exceed +2° relative to the axis centerline (as shown in Figure 2).
(5) Installation of Slider Blocks
Slider blocks are installed between two parallel guide rails and can be moved along the guide rails by adjusting bolts to achieve the purpose of adjusting the center distance of the shaft. The relevant mating parts are shown in the following figure.
The installation dimensions and tolerances of the slider blocks are according to the specifications of the round nuts and bolts.
Maintenance of Mounted Bearings
To fully utilize and maintain the desired performance of bearings for a long time, it is necessary to carry out regular maintenance and inspections.
1. When dismantling the bearing for inspection, first take a visual record using photography or other methods. Additionally, confirm the remaining lubricant quantity, take a sample of the lubricant, and then clean the bearing.
Note: Commonly used cleaning agents include neutral water-free diesel or kerosene, and warm alkaline solution may also be used as needed. Regardless of the cleaning agent used, it should be regularly filtered to maintain cleanliness. Immediately after cleaning, apply rust-preventive oil or grease to the bearing.
1. To determine if the dismantled bearing can be reused, focus on checking its dimensional accuracy, rotational accuracy, internal clearance, as well as the mating surface, raceway surface, cage, and sealing ring. Regarding the inspection results, a judgment can be made by someone accustomed to or proficient in bearings.
Note: The criteria for judgment vary depending on the mechanical properties, importance, inspection cycle, etc. Bearings with the following damages should not be reused and must be replaced.
Englisch.
Im namen der russischen föderation
Spanisch. Danke.
italien
Auf arabisch!
Es ist koreanisch.
In deutschland.
Nach japan.
vietnam
Die türkei.
Vorstellung.
Italien. - vergiss das nicht.
Laden!
